On Tuesday, December 14, 2021, the German University of Technology in Oman, GUtech, completed 3D printing the walls of what so far is the largest 3D printed building in made with real concrete. The importance of the event was marked by the presence of His Excellency Sultan Al-Habsi, Minister of Finance of Oman together with more than 200 guests including several ministers and VIPs of Oman, who attended the event in Muscat, the capital of Oman.

The house consists of 190 m2 (2,100 sqf) and is typical for a social housing unit in Oman. It has 3 bedrooms, three bathrooms, a living room, kitchen, and guest reception area. The house was printed in two stages. While the materials recipe was adjusted and training of the Omani crew took place during the printing of the first part of the house, the second part of the house was done by the Omani crew on their own and it only took five days to complete. A sign of fast learning and productivity improvements occurring in 3D printed projects.

Dr. Hussain, Acting Rector of GUtech said “Today’s display of the first 3D printed building is perhaps the first step in the 1,000-mile journey. A step that will not be successful without the support of all parties involved. In this regard, I sincerely thank all the local and international parties who contribute to supporting the center and the University. We hope that this center will play its part in supporting Oman’s efforts to achieve Oman’s Vision 2040.”

While the Middle East has seen numerous 3D printed buildings, the 190 m2 (2,100 sqf) building in Oman is the first to be printed with real concrete instead of the traditional dry mix mortars used in most other 3D printed buildings. To make the concrete 3D printable, GUtech applied the D.fab solution developed by COBOD and CEMEX in cooperation where the concrete can have particle sizes up to 10 mm (1/3 inch) and is made from locally available cement, sand, and gravel. CEMEX and COBOD launched the news about the D.fab solution last week in connection with the first 3D printed building in Angola. The D.fab solution was also used in Angola with the result that the cost of the concrete materials was less than 1,000 USD for the 52 m2 (575 SF) house.

On that occasion, Juan Romero, Executive Vice President Sustainability, Commercial, and Operations Development of CEMEX said: “The introduction of this revolutionary 3D printing system is a testament to our customer-centric mindset and relentless focus on continuous innovation and improvement. Working together with COBOD, we have developed an experience for customers that is superior to anything that has been provided in the past”.

In the case of Oman, more than 99.5% of the materials used were local, with less than 0.5% coming from Europe in the form of the D.fab additives. In Oman, the cost of materials for 3D printing of the walls of the 190 m2 (2.100 SF) house was less than 1,600 Euro. According to COBOD, if a printable dry mix mortar had been used the cost of the materials would be more than 20,000 Euro, and it was such significant cost reductions that COBOD and CEMEX were aiming for with their cooperation.

Commenting on this milestone for the widespread adoption of the 3D construction printing method, Henrik Lund-Nielsen, Founder & General Manager of COBOD International stated: “While we have been happy to help various cement and concrete manufacturers develop dry mix 3D printable mortars, we have also insisted on that a solution for making real concrete made from locally available materials would be needed for mass application of our technology. We are more than pleased that CEMEX took on the challenge and proud that we in cooperation could develop the new solution, which GUtech has now applied to the first building in Oman. With the low cost for the printed materials, on top of the savings from not needing formwork and the minimal crew needed to operate our printers, our disruptive technology is now more competitive than ever before in Oman and everywhere in the world”.

This market study from 3dpbm Research provides an in-depth analysis and forecast of the ceramic additive ma...

Your email address will not be published.

Save my name, email, and website in this browser for the next time I comment.

I’ve read and accept the privacy policy. *

I’ve read and accept the privacy policy.*

I’ve read and accept the privacy policy.*

We use cookies to give you the best online experience. By agreeing you accept the use of cookies in accordance with our cookie policy.

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

Join industry leaders and receive the latest insights on what really matters in AM!

This information will never be shared with 3rd parties

I’ve read and accept the privacy policy.*